15 Channel Remote instructions

 Important

Some operations require two buttons on the remote to be pressed simultaneously. Sometimes, it could be hard to tell whether the buttons are being pressed at the same time. As such, the LCD display on the remote will indicate when two buttons are being pressed simultaneously by showing the gear cog icon.

Pairing to a remote

Follow these steps to pair the motor to a channel on the remote:

  1. Press and hold the PROG button on the motoruntil the status LED turns solid green.
  2. Select the desired channel on the remote control.
  3. Press and hold the OPEN and CLOSE buttons on the remote.
  4. After 3-5 seconds, the motor will jog to indicate successful pairing. The status LED will also flash green twice, then turn off.
  5. Pairing is now complete.

Limit setting

 Important

Must be completed after the motor is paired to the remote.

Follow these steps to set travel limits using the remote:

  1. On the remote, select the channel the motor is paired to.
  2. Press and hold the P1 and P3 buttons on the remote.
  3. After 3-5 seconds, the motor will jog to indicate it has entered config mode.
  4. Using the OPEN and CLOSE buttons, position the roller shade to the desired lower limit. Note that in config mode, the motor response is momentary to latch. This means that if the OPEN or CLOSE button is pressed down for less than 3 seconds, the motor will stop immediately upon button release. If the button is held for more than 3 seconds, the motor will keep running until the STOP button is pressed.
  5. (If applicable) If the movement direction of the roller shade is opposite to that of the button being pressed, press and hold the OPEN and CLOSE buttons until motor jogs to reverse the running direction.
  6. Press and hold the P2 and P3 buttons until motor jogs to save the current position as the lower limit.
  7. Using the OPEN and CLOSE buttons, position the roller shade to the desired upper limit.
  8. Press and hold the P1 and P2 buttons until motor jogs to save the current position as the upper limit.
  9. Press and hold the STOP button until motor jogs to exit config mode.

Intermediate position setting

 Important

Must be completed after limit setting.

In addition to the lower and upper limit positions, the motor also has 3 additional preset positions, also called intermediate positions. By default, the P1, P2 and P3 buttons correspond to 25% closed, 50% closed and 75% closed positions respectively.

Follow these steps to customise intermediate positions:

  1. On the remote, select the channel the motor is paired to.
  2. Press and hold the P1 and P3 buttons on the remote.
  3. After 3-5 seconds, the motor will jog to indicate it has entered config mode.
  4. Using the OPEN and CLOSE buttons, position the roller shade to the desired intermediate position.
  5. Press and hold the desired intermediate position button (P1, P2 or P3) until motor jogs to save the current position.
  6. Press and hold the STOP button until motor jogs to exit config mode.

Changing travel directions (only applicable to roller blind motors)

 Important

Must be completed after limit setting.

Follow these steps to change the direction of the motor spin:

  1. On the remote, select the channel the motor is paired to.
  2. Press and hold the P1 and P3 buttons on the remote.
  3. After 3-5 seconds, the motor will jog to indicate it has entered config mode.
  4. Press and hold the OPEN and CLOSE buttons on the remote.
  5. After 3-5 seconds, the motor will jog to indicate it has changed directions.
  6. Press and hold the STOP button until motor jogs to exit config mode.

Deleting a paired channel

 Important

Must be completed after pairing.

Follow these steps to cancel an already paired channel:

  1. On the remote, select the channel the motor is paired to.
  2. Press and hold the P1 and P3 buttons on the remote.
  3. After 3-5 seconds, the motor will jog to indicate it has entered config mode.On the remote, select the channel the motor is paired to.
  4. Press and hold OPEN and CLOSE buttons on the remote.
  5. After 3-5 seconds, the motor will jog to indicate it is no longer paired to that channel.
  6. Press and hold the STOP button until motor jogs to exit config mode.

Cycle through channels

Use the < and > buttons.

Shortcut to ALL channel

Press both the < and > buttons simultaneously.

Change the total number of channels

  1. Press and hold both the < and > buttons until the LCD shows the current top channel number flashing.
  2. Use the < and > buttons to select the desired top channel number.
  3. Press the STOP button to confirm.

Standard operation

Button

Function

< 

Select previous channel

> 

Select next channel

OPEN

Move to upper limit position

STOP

Stop the motor

CLOSE

Move to the lower limit position

P1

Move to first intermediate position (default 25% closed)

P2

Move to second intermediate position (default 50% closed)

P3

Move to third intermediate position (default 75% closed)